Oct. 3, 2000
NASA Ames Research Center, Moffett Field, CA
650/604-5026 or 604-9000 email@example.com
NASA DEVELOPING "SNAKEBOT" TO EXPLORE AND BUILD IN SPACE
NASA engineers are developing an intelligent robot snake that may help explore other worlds and perform construction tasks in space.
The robot serpent, able to independently dig in loose extraterrestrial soil, smart enough to slither into cracks in a planets surface and capable of planning routes over or around obstacles, could be ready for space travel in five years, NASA engineers predict.
"The snake will provide us with flexibility and robustness in space," said Gary Haith, lead "snakebot" engineer at NASAs Ames Research Center located in Californias Silicon Valley. "A snakebot could navigate over rough, steep terrain where a wheeled robotic rover would likely get stuck or topple."
"One of our first steps was to make a simple mechanical test snake, and we constructed it in less than a day thanks to previous work at other labs," said Haith. "It is a direct model of a polybot developed by Mark Yim of Xerox Palo Alto Research Center, Palo Alto, CA, with whom we are cooperating. We have slightly different electronics in our version."
"The test snake has a wire that carries communications and power to and from the computer brain," Haith explained. "All of the identical hinge-like modules are easy to make, and we attached the snake segments together in a chain. It has off-the-shelf hobby motors in its hinged segments that cause it to move. Each of the many motors takes a signal from the snakes main computer brain," he said.
"Our first test robot does what we tell it to do, no matter what the results are. If it comes to an obstacle, the robot will continue to try to go over it, even if the task is impossible," he said. "We made the first, simple robot because we wanted a working snakebot in a day or two, a robot that would help us to think about how a snakebot could and should move."
Robotic serpents can "inchworm" ahead, can flip themselves backward over low obstacles, can coil and can side-wind, Haith said. "Future work will enable the snake to become a mast or a grasping arm. A rover would need to have a dedicated mast and arm that would cost extra weight, money and time."
"A snakebot is not as good at some jobs as other robots, but you get a lot more robot for the weight and the money," he said. "The problem is its hard to tell the snakebot what to do. It is a complex robot that must operate independently, possibly far from Earth. Work on our second snakebot is aimed at making it capable of independent behavior."
"The key part of what we are striving for in the second snakebot version and beyond is sensor-based control in which the robot uses its sensors to decide what to do," Haith said. "We made two little microcontrollers, tiny computers, that we put in each hinged section that also includes a motor, electronics and gears to get the hinge to move to certain positions," he explained.
The snakebot will have a main computer that will tell its little computers in each segment what to do in a higher, planning sense. The tiny computers in the segments could provide "reflexes" that take care of simple, but important jobs.
"In the next couple of months, we hope to simulate the snakebot in a computer program so we can automatically develop computer routines that can control the robot," Haith said. Engineers have added strain sensors to the robot on metal ribs inside the snake. "They will tell the snake whether or not it is contacting anything, and where and how hard it is touching," Haith explained.
"We hope to write software that allows the snake to learn on its own by experience," he said. "Some lessons we hope it will learn are how to crawl from soft to hard surfaces, and how to go over rough surfaces that have rocks. We even hope to show that it can climb scaffolds and go into cracks. These abilities would help the robot look for fossils or water on another planet," he added.
The snakebot can save spacecraft weight because the snake-like design enables the robot to do many tasks without much extra equipment, according to engineers. "One of the many advantages of the snake-based design is that the robot is field-repairable. We can include a bunch of identical spare modules with the snake on a space mission, and then we can fix the snakebot much easier than a regular robot that needs specific parts," said Haith. "Other benefits are: the snakebot can crawl off a spacecraft lander and doesnt need a ramp, the snake's moving parts can be sealed inside artificial skin to avoid exposure to the outside environment and the robot can still function, even if one joint freezes."
"In coming years, we hope to make snakebot muscles out of artificial plastic or rubber materials that will bend when electricity is applied to them," he added. "This design change will reduce the snake's weight considerably, and the robot would be very robust, like an automobile tire," For more technical robotic snake information, please visit the NASA snakebot Internet site at: http://ic-www.arc.nasa.gov/ic/snakebot/
NOTE TO BROADCASTERS: Broadcasters may downlink NASA satellite "video file" footage related to this story, today, Oct. 3, 2000. There also may be re-feeds of the story on Oct. 4.
After Oct. 4, depending upon satellite availability, additional re-feeds of the material may also be available; please telephone Ray Castillo at 202-358-4555 or Fred Brown at 202-358-0713 in Washington, DC, to make a re-feed request.
Please note that all TV feed times, unless otherwise listed, are Eastern Times. The NASA Video File normally airs at 12:00 p.m., 3:00 p.m., 6:00 p.m., 9:00 p.m. and 12:00 a.m. EDT. NASA Television is available on GE-2, transponder 9C at 85 degrees West longitude, with vertical polarization.
Frequency is on 3880.0 Megahertz, with audio on 6.8 Megahertz. Any changes to the line-up will appear on the NASA video file advisory on the web at ftp://ftp.hq.nasa.gov/pub/pao/tv-advisory/nasa-tv.txt
- end -
To receive Ames news releases via e-mail, send an e-mail with the word "subscribe" in the subject line to firstname.lastname@example.org. To unsubscribe, send an e-mail to the same address with "unsubscribe" in the subject line.